- Home
- courses
- Admissions
- Training & Placements
- contact us
- Alumni
- Blog
- +91-8607788739 / 40
Mr. Madhavendra Singh Gautam
Assistant Professor
Coordinator Department of Mechanical/Automobile Engineering
EDUCATION
PROFESSIONAL EXPERIENCE
RESPONSIBILITIES AT WCTM
AWARDS, HONORS AND FELLOWSHIPS
CERTIFICATIONS AND SHORT TERM COURSES
PUBLICATIONS AND PRESENTATIONS
RESEARCH SUMMARY
Mr. M.S. Gautam’s research work is concerned with the optimization of specific work output and thermal efficiency of the combined cycle at a different air-fuel ratio, pressure ratio and variable supplementary heating. In the present paper the pressure ratio has been taken in the range of 4 to 20 bar, air-fuel ratio 50, 55, 60, and 65 and supplementary heating from 0.1 to 0.5. It is observed that specific work output and thermal efficiency improve at the lower air-fuel ratio, pressure ratio and supplementary heating. In the present analysis effect of supplementary heating on the performance of combined cycle is discussed. It was desirable that at the (exhaust temp. of gas turbine t4a + gas turbine bypassed temp. t3) should be above 813 K; otherwise, the steam cycle would be inefficient resulting in lower combined cycle plant efficiency.
Mr. Ravinder Kumar Anand
Assistant Professor
Department Of Mechanical/Automobile Engineering
EDUCATION
PROFESSIONAL EXPERIENCE
INDUSTRIAL : 4.9 years
TEACHING : 14 years
A). Teaching :- 18 Years
1) Working as an assistant professor at World College of Technology & Management, Gurugram, since January 2016.
2) As an assistant professor at Panipat Institute of Engineering and Technology, Panipat from October 2014 to May 2015.
3) As a principal at S.S. College of Polytechnic, Karnal from November 2008 to October 2014.
4) As an assistant professor at Panipat Institute of Engineering and Technology, Panipat from August 2008 to November 2008.
5) As a lecturer, senior lecturer and assistant professor at Inderprastha Engineering College, Ghaziabad from August 2001 to August 2008.
B). Industry :- 4.9 Years
1) Worked at Bhushan Steel & Strips Limited, Site-4, Industrial Area, Sahibabad, Ghaziabad from November 1996 to August 2001 as a maintenance engineer.
CERTIFICATIONS AND SHORT TERM COURSES
1) One week short-term course on TQM at NITTTR, Chandigarh.
2) International conference on “Challenges and Strategies for Sustainable Energy, Efficiency and Environment” at UPTU Lucknow.
3) AICTE sponsored National workshop on “Advances in Arc Welding Processes” organized by Krishna Institute of Engineering and Technology in collaboration with Indian Institute of Welding.
PUBLICATIONS AND CONFERENCE
Journals:
1. ‘Complexity analysis of Mechanical Assemblies’ (2007) in Journal of Intelligent System Research, January - June 2007; pp 1-9
2. ‘History of cause-effect relationship between whole-body vibrations and musculoskeletal disorders in truck drivers’ in ELK Asia Pacific Journals – Special Issue 2016, ISBN: 978-81-930411-8-5 conferences;
1. ‘Some aspects of Flexible Manufacturing System (FMS) in Indian Manufacturing Industries’ (2006) in national conference on Advances in Mechanical Engineering (AIME- 2006), January 20-21, 2006, Jamia Millia Islamia, New Delhi, pp 449-456.
2. ‘Conflicts between DFA and DFM- How to find the best solution’ (2006) in National Conference on Recent Developments and Future Trends in Mechanical Engineering (RDFTME-2006), November 3-4, 2006 NIT, Hamirpur (HP), pp 235-245.
3. ‘Design for Low Cost - A solution to the Conflict between DFM & DFA’ in National Conference on Trends & Advances in Mechanical Engineering December 9-10, 2006, YMCA Institute of Engineering, Faridabad, Haryana, pp 549-554.
4. ‘Linking modularity and flexibility to DFM/ DFA contradiction’ in AICTE sponsored national level seminar on Robotic and Automation, March 30-31, 2007, N.C. College of Engineering, Israna (Panipat), pp 10.
5. ‘Case study of Paharpur Cooling Towers Ltd.’ in AICTE sponsored national level seminar on Robotic and Automation, March 30-31, 2007, N.C. College of Engineering, Israna (Panipat), pp 5.
6. 'A literature survey on Ergonomical Problems of Vehicle Drivers’ in International Conference on Manufacturing Excellence (MANFEX 2017) pp 279-284.
RESEARCH SUMMARY
Ph.D (Pursuing) – Amity University, Noida
Mr. Shashi Bhushan Prasad
Assistant Professor
Department Of Mechanical/Automobile Engineering
EDUCATION
PROFESSIONAL EXPERIENCE
RESPONSIBILITIES AT WCTM
Mr. Desh Deepak
Associate Professor
Department Of Mechanical/Automobile Engineering
EDUCATION
PROFESSIONAL EXPERIENCE
RESPONSIBILITIES AT WCTM
CERTIFICATIONS AND SHORT TERM COURSES
PUBLICATIONS AND PRESENTATIONS
RESEARCH SUMMARY
Mr. D. Deepak’s research work is concerned with the accurate determination of Hydrodynamic Coefficient of an underwater vehicle using CFD. The focus has been on accurate detailing of flows using CFD applying higher computational power, making it expensive. The derivatives obtained from the simulation of the quasi‐static drift of the body with zero degree stern and rudder angle at various angles of attack and angular velocities give the stability HDCs. Stern and rudder angle control submarine motion and the simulation of the quasi‐static drift of the body with non‐zero degree stern and rudder angles give the control HDCs. This approach allows the development of templates ‐ which mesh and execute a set of quasi‐static CFD simulations to arrive at the values of the stability and control HDCs using modest computational resources and cost ‐ for trajectory simulations of concept designs of underwater vehicles without expensive real-time CFD simulations of these motions.
Dr. Brajendra Nath Tripathi
Associate Professor
Department Of Mechanical/Automobile Engineering
PROFESSIONAL EXPERIENCE
Teaching : 14 yrs.
Industry : 5 yrs.
Worked for 5 years in Atul Glass Industries Ltd., Faridabad, Haryana.
RESPONSIBILITIES AT WCTM
Teach Fluid Mechanics, to undergraduate students of mechanical engineering.
PUBLICATIONS & PRESENTATIONS
1. Presented a paper on ‘Condition monitoring of Rotating Equipment in plants using vibration analysis’ at the National Seminar on ‘Advances in Mechanical Engineering’ held at Gurgaon Institute of Technology & Management, Gurgaon on 21st & 22nd February 2014.
2. Presented a paper on ‘Advances in the Shaft Sealing System of Centrifugal Pumps’ at the National Seminar on ‘Advances in Mechanical Engineering’ held at Dronacharya College of Engineering, Gurgaon on 22nd July 2009.
3. Presented a Paper on ‘Condition Monitoring’ at NFL Bathinda at a seminar organized by National Productivity Council, New Delhi for senior engineers on 21st March 2000.
4. Paper ‘Problem Faced on Steam Turbine at NFL Bathinda, a Case Study’ was published in ‘Fertilizer News’ (a technical journal published by Fertilizer Association of India, New Delhi) in its February 1994 edition.
5. Paper ‘Failure of Ball Bearings & its Diagnosis by Vibration Analysis’ was published in ‘Chemical Engineering World’ in its May 1989 edition.
6. Paper ‘Air Compressor Failure’ at NFL Panipat, a case history was published in ‘Fertilizer News’ in its November 1986 edition.
Mr. Vinay Kumar Sharma
Professor
Department Of Mechanical/Automobile Engineering
EDUCATION
B.Sc. (Engg.) Mechanical, Regional Engineering College, Rourkela (now NIT) 1971 M.E. (M.Tech.) M/c Design, University of Roorkee, Roorkee (now IIT) 1974
PROFESSIONAL EXPERIENCE
Teaching : 7.5 yrs.
Industry : 32 yrs.
(i) Worked for 27 years in Fertilizer Corporation of India Limited & National Fertilizers Ltd. (A Govt. of India Undertaking) & held the post of chief manager when left.
(ii) Worked for 5 yrs in Bandar Imam Petrochemical Co, Bandar Imam, Iran & Fanavaran Petrochemical Company, Bandar Imam, Iran, as a specialist mechanical engineer for condition monitoring & maintenance of rotating equipment.
SPECIAL TRAINING
RESPONSIBILITIES AT WCTM
Teaches Strength of materials, Mechanical Machine Design & Power Plant Engineering to the undergraduate students of Mechanical Engineering.
PUBLICATIONS & PRESENTATIONS
Publications & Presentations
1. Presented a paper on ‘Condition Monitoring of rotating equipment in Plant using Vibration Analysis’ at the National Seminar on ‘Advances in Mechanical Engineering’ held at Gurgaon Institute of Technology & Management, Gurgaon on 21st & 22nd February 2014.
2. Presented a paper on ‘Advances in the Shaft Sealing System of Centrifugal Pumps’ at the National Seminar on ‘Advances in Mechanical Engineering’ held at Dronacharya College of Engineering, Gurgaon on 22nd July 2009.
3. Presented a paper on ‘Condition Monitoring’ at NFL Bathinda at a seminar organized by National Productivity Council, New Delhi for Senior Engineers on 21st March 2000.
4. Paper ‘Problem Faced on Steam Turbine’ at NFL Bathinda, a case study was published in ‘Fertilizer News’ (A technical journal published by Fertilizer Association of India, New Delhi) in its February 1994 edition.
5. Paper ‘Failure of Ball Bearings & its Diagnosis by Vibration Analysis’ was published in ‘Chemical Engineering World’ in its May 1989 edition.
6. Paper ‘Air Compressor Failure’ at NFL, Panipat, a case history was published in ‘Fertilizer News’ in its November 1986 edition.
Mr. Prasanta Kumar Paul
Assistant Professor
Department Mechanical/Automobile Engineering
Mr. Prasanta Kumar Paul is a professor in the Department of Mechanical Engineering. He is a Post-graduate in Mechanical Engineering with a proven track record first in the industry and then in academics as a consultant, designer, manager, teacher, mentor and can assess the potential of people to decide progress methodology for further growth. He has 40 years of industrial and teaching experience. Mr Paul’s industrial experience covers large chemical plant design, project management, construction while his teaching experience covers training of industrial trainees, undergraduate and postgraduate students of engineering in India, Italy, Iran and Abu Dhabi. He was associated with Engineers India Limited, New Delhi, Triune Energy, Delhi, Skyline Institute of Engineering & Technology, Greater Noida, and JIS College of Engineering, Kalyani near Kolkata.
Mr. Anil Kumar Sarkar
Assistant Professor
Department Of Mechanical /Automobile Engineering
EDUCATION
PROFESSIONAL EXPERIENCE
RESPONSIBILITIES AT WCTM
TRAINING , WORKSHOP AND SHORT TERM COURSES
PUBLICATIONS AND PRESENTATIONS
INDUSTRIAL EXPERIENCE SUMMARY
Mr. Anil Kumar Sarkar has 34 years of experience in the refining industry. The different activities covered are Maintenance of Refinery Equipment like turbine, compressors, high-pressure pumps, furnace, columns, water treatment plants, construction & commissioning of the grassroots refinery as Deputy General Manager.
Mr. Deepak Sharma
Assistant Professor
Department Of Mechanical/Automobile Engineering
EDUCATION:
PROFESSIONAL EXPERIENCE
INDUSTRIAL: 02
TEACHING: 07
(Summary of Experience)
RESPONSIBILITIES AT WCTM
CERTIFICATIONS AND SHORT TERM COURSES
PUBLICATIONS AND CONFERENCE
RESEARCH SUMMARY
Pursuing PhD. in Mechanical Engineering from Shri Mata Vaishno Devi University, Katra, Jammu and Kashmir under the guidance of Dr. Rajesh Kumar Bhushan (Associate Professor, Mechanical Engineering, Guru Ghasidas University, a central university, Bilaspur, Chhattisgarh).
Registration no. : 12PHDEME01
Area of Research : Friction Stir Welding of Metal Matrix Composites
Status of Research : At the final stage of experiments and testing at IIT, Gandhi Nagar
Mr. Gurdeep Singh Grewal
Assistant Professor
Department Mechanical/Automobile Engineering
Gurdeep Singh Grewal is an assistant professor in the Department of Mechanical/Automobile Engineering. He is M.Tech. with specialization in Manufacturing and Automation from M.D.U, B.Tech in Mechanical Engineering from Punjab Technical University. He has five years of teaching experience and teaches various subjects like Material Science and Engineering, Automobile Engineering, Theory of Machines, Fluid Machines, Engineering Drawing and Basics of Mechanical Engineering at the graduate level in Engineering colleges.
His research work is concerned with the mechanical properties of Aluminium Honeycomb Structure. He has also presented a paper titled as “Evaluation of Mechanical Properties of Aluminium Honeycomb Sandwich Panel with Different Cell Sizes” at international journal of R&D in engineering science and management.
Mr. Omprakash Prajapati
Assistant Professor
Department Of Mechanical Engineering
EDUCATION
PROFESSIONAL EXPERIENCE
RESPONSIBILITIES AT WCTM
